Skip to main content

Car Washing, hose foam spray gun VS pressure washer foam sprayer

Hello this is a write up comparing a few different options when selecting a foam distribution system for cleaning your automobile the Gilmour Cleaning Sprayer, Greenworks 1700 PSI Pressure Washer, and the additional Greenworks High Pressure Soap Adapter .



The best budget friendly winner is the Gilmour Cleaning Sprayer as it uses your existing hose and can generate a very decent amount of foam for your car washing. It is recommended by AMMO NYC, a very great youtube channel about car care and retailer of products to care for your automobile as well. The image below is shown being applied to my drive way for good contrast to show the different levels of foam from the gilmour option.


The winner of it all is the greenworks pressure washer with the high pressure soap adapter from green works with the additional High Pressure soap adapter.


The loser is the soap sprayer that comes with the pressure washer, it is awful and should not be used at all just recycle it, as it is good for nothing a hose and bucket is a better soap dispenser. as shown below it is just wet, not high pressure, and barely dispenses any soap.


Below is a video showing them being used with the same batch of soap and water being transferred between all three to show the difference with a consistent mixture.



Thanks for reading and enjoy your clean car.

Links below are amazon affiliate links.

Portland, ME 04101, USA

Comments

  1. Sound Deadening StoreFebruary 25, 2022 at 6:55 AM

    The Sound Deadening Store offers Vast range of Sound Deadening Mats. Buy our sound deadening for cars are made with high quality of material which make them 100% Soundproof.

    ReplyDelete
  2. Sound Deadening StoreAugust 11, 2023 at 2:44 AM

    Your content resonates deeply with those in the admin world. Thank you for your valuable contributions Your dedication to producing high-quality admin content is both admirable and impactful. Your blog is a sanctuary of admin wisdom. Your dedication shines through every post thermal insulation sheet

    ReplyDelete

Post a Comment

Popular posts from this blog

MazdaSpeed 3 2008 Idler / Tensioner Pulleys and Belt

Changing the idler pulley, serpentine belt and tension pulley on a 2008 MazdaSpeed 3 is quite easy ( I do not know if this all applies to the regular Mazda 3) and can be completed in a couple hours. I got all my parts from Napa www.napaonline.com  / good luck 1. Set the e-brake 2. Loosen the Lug nuts on the Front Passenger Tire 3. Jack the front of the car and support on jack stands 4. Remove the front Passenger tire 5. Remove the bolts that attach the small plastic splash guard toward the front of the fender well ( this gives you a bit more room for getting at the idler)  (A view from the top of the engine bay) 6. Use a Combo Wrench on the Tensioner Pulley to slack the belt and slide it off the pulley (Turn the wrench Clock-Wise to slack the belt, note that there is a notch so that the Tensioner can only rotate so far so do not exert the Tensioner beyond the point it feels it stops rotating) 7. Remove the two bolts that hold t...
8 comments
Read more

2008 MazdaSpeed3 Purge Valve Replacement

Purge Valve Replacement on a 2008 Mazdaspeed3, I recently was having a hard start after refueling, the car would start and idle at 500 rpm and barely run and would stall but would restart and with a quick gas pedal press it would run fine once it idled out. So I googled a bit and found that it was the purge valve.  I bought one from AMAZON.com  the Dorman 911-702 Mazda 6 Purge Valve Start by removing the Inter-cooler Cover Screws and the plastic guard. Locate the Purge Valve (in between the inter-cooler and the battery box) Remove the hose guarding to get to the clamps and remove the power connector to the purge valve Remove the Hose Clamps and slide off the Purge Valve The rubber mount will not be in the Same Orientation  Remove the Rubber mount from the new one and align to be the same as the one you just removed Re-install in the reverse order and Enjoy your speed again Amazon Affiliate Links used in po...
3 comments
Read more

Mazdaspeed3 Gen1 2008 Rear sway arm bushings and stabilizer links

Warning ! working on your own car is dangerous and all parts listed below are not guaranteed to work in your case so do your homework. this is just a guide of what I did to remedy a problem and how I was able to trouble shoot and resolve my issue as inexpensively as possible. For a little while now I had been getting the dreaded rear "clink clunk" of the sway bar when going over bumps slowly. I had ordered and installed the Moog sway bar bushing s and sway bar links in April 2016. The originals had lasted since 08, at least the records I have and for sure since 2012 when I bought the car. I am trying the Febest sway bar links  and Febest sway bar bushings  this time around as I though the moogs would have lasted longer and was not super happy with the boot design on the sway bar links. Tools required-ish: (depending on your current type of sway bar links) Hammer to start the bolts loose as there is limited space to get a longer ratchet under car for some of these 6...
Post a Comment
Read more